A new-build guest room should not be specified around a basic captive key-card switch alone. Occupancy sensing — PIR and door-contact signals tied into the guest-room control system — reports a richer occupancy state into the Guest Room Management System (GRMS) and can drive an exit sequence across lighting, shading, HVAC, and audio/video, not just one circuit. A captive card switch may still have a role as a simple fallback, but ask your integrator exactly what it does and doesn't reach before relying on it as the primary energy-management layer.
What does occupancy sensing actually switch off?
Crestron's hospitality guest-room material describes presence-detection sensors that verify occupancy and report it to the GRMS when a guest enters. On departure, "integrated door lock systems activate a smooth, energy-saving exit automation process: lights turn off, shades and drapes close, HVAC adjusts to eco mode, audio mutes or powers off, and the TV shuts off" (Hospitality Guest Rooms, Crestron Electronics). That sequence is tied to the door lock and occupancy sensor state rather than to a single switch, and it reaches several systems in one event instead of one lighting circuit.
Crestron's standard guest-room package is described as requiring no processor and including a master on/off switch for the whole room, with occupancy sensors layered in for energy savings and compatibility with PMS and BMS through the GRMS for manager-level oversight. That combination — a master switch plus sensing plus PMS/BMS reporting — is the baseline the current guest-room product generation is built around, not an add-on. Exactly what a basic captive card-key switch alone can and cannot control on a given platform is a question to put directly to your electrical contractor or guest-room system integrator, since no single spec sheet covers every manufacturer's card-switch wiring the same way.
What should stay live regardless of which method is used?
Whatever exit-automation approach a property specifies, the departure sequence still needs exceptions carved out for device-charging receptacles and any life-safety circuits — those should never follow the same off command as room lighting. This is a design decision to confirm with your electrical and HVAC contractor rather than something to assume by default, and the exempted circuit list should be documented and signed off in the mockup room before it rolls out to every floor.
How does PMS status add a setback tier beyond simple occupancy?
Occupancy sensing that reports into the GRMS, and from there into the PMS, can add a tier that pure presence detection alone doesn't capture: whether the room is sold for the night at all. Mews describes this pattern in its MClimate Enterprise Integration, where "at check-in, devices switch from an energy-saving to a comfort schedule, and at check-out, devices revert to predefined setback or eco profiles," connecting smart radiator valves, HVAC controllers, and environmental sensors to real-time occupancy data from the PMS (Mews x MClimate Enterprise Integration, Mews). That check-in/check-out event comes from the reservation record itself, which gives the system a sold/unsold distinction layered on top of whatever a room's own sensors detect.
Which approach should a new build specify?
Ask whether a proposed guest-room platform's standard package already bundles occupancy sensors, a master switch, and PMS/BMS reporting — Crestron's standard guest-room offering does, which is a reasonable signal that sensing tied to the GRMS is the current baseline rather than an upgrade bolted on later. Whether a standalone captive card switch can be wired to reach HVAC or receptacle loads, and whether it can carry any sold/unsold signal from the PMS, varies by manufacturer and should be confirmed directly with the platform vendor rather than assumed. For a hospitality project, this decision belongs in the same conversation as PMS selection, lock credential design, and guest-room keypad layout — not treated as an afterthought once construction is underway. Cave Group's hospitality practice builds custom guest-room automation on Crestron, or on Lutron myRoom where a packaged platform fits, with PMS integration handled as part of the same design.
If the property is renovating an existing building rather than building new, review how PIR, door contacts, and keycard signals already combine inside the installed GRMS before assuming a wholesale sensor retrofit is required — see How Guest-Room Occupancy Sensing Really Works for how those signals are weighed together, and Hotel Energy Reporting: How PMS Drives Room Setbacks for how the resulting setback data flows to a BMS for ESG reporting.
Frequently asked questions
Can occupancy sensing control HVAC the way a card switch does?
Occupancy sensing reporting into a GRMS can extend exit automation to HVAC eco-mode setback as part of the same departure sequence, alongside lighting, shading, and audio/video, as Crestron's guest-room description outlines. Whether a standalone captive card switch can be wired to reach HVAC on a given platform is a question to confirm directly with your electrical contractor or integrator.
Does PMS sold/unsold status change how deep a room can set back?
Yes. Integrations like Mews's MClimate connection shift HVAC devices between a comfort schedule at check-in and a deeper eco or setback profile at check-out, driven by the reservation record itself rather than by room sensors alone.
Should devices always lose power when a guest leaves?
No — any exit automation design should carve out an exception for device-charging receptacles and any life-safety circuits. Confirm the exempted list with your electrical contractor before it's locked into the mockup room.
Is a captive card switch ever still a reasonable choice?
It may function as a simple fallback, but current guest-room platforms bundle occupancy sensors, a master switch, and PMS/BMS reporting into their standard packages, which suggests sensing tied to the GRMS is the baseline for a new installation. Confirm what a specific card-switch product can and can't control with the manufacturer before relying on it as the primary energy layer.
What should I ask my integrator before locking this decision in?
Ask how exit automation divides lighting, shading, HVAC, and audio/video control on the platform being proposed, how that automation links to your PMS for sold/unsold status, and exactly what loads a standalone card switch would and wouldn't reach on that same platform.