Setting up a leased office network means sorting out the telecom room and ISP demarc with the landlord before signing, then building one topology where a gateway, switch, and Wi-Fi 7 access points carry separate VLANs for staff, guests, payment terminals, cameras, and door access. Door access for a leased suite is handled with a dedicated access hub and reader at the suite entrance, not a residential gate controller. After move-in, the network should report into a cloud dashboard so firmware and uptime are monitored remotely rather than discovered when something breaks.
A small office tenant signing a lease rarely gets to choose how the building's riser or ISP demarc is built, but asking the right questions before signing avoids rework after the fit-out starts. Below is the sequence a tenant should walk through, from lease questions to the rack itself, and what to expect once the system is live.
What should you ask the landlord before signing?
Before signing, find out where the building's telecom room sits relative to your suite, whether the ISP demarc already terminates there or needs a new drop, and whether the landlord restricts contractor access to the riser. A long run from demarc to suite affects cabling cost and the switch placement inside the office. These answers also tell you whether your fit-out schedule depends on building engineering sign-off, which is common in multi-tenant NYC properties.
How do the gateway, switch, and access points fit together?
A small office network is really three layers working as one system: a security gateway at the edge, a PoE switch distributing power and data, and Wi-Fi 7 access points serving staff and guest devices. Ubiquiti's current Enterprise-tier gateways (EF-Core or EFG) sit at the edge, an Enterprise Campus switch distributes PoE+++ to access points and other devices with hardware-accelerated Layer 3 inter-VLAN routing available on Professional, Pro Max, and Enterprise switch families (UniFi Switching), and Wi-Fi 7 access points in the Enterprise series connect over 10 GbE uplinks and can serve 1,000+ connected devices per access point depending on model. For a single-floor leased suite, this usually means one gateway, one switch, and one or two access points rather than the larger campus stacking options built for multi-building properties.
Layer 3 switching matters here because it lets the switch itself route between VLANs in hardware rather than sending every cross-VLAN packet back to the gateway, which keeps a small office network responsive even as more devices and segments are added.
How should staff, guest, and payment-terminal traffic be separated?
Separate VLANs keep staff computers, guest Wi-Fi, payment terminals, cameras, and the door access system from seeing each other's traffic, so a compromised guest device or a vulnerable camera can't reach the business's financial systems or staff files. This is standard practice on any UniFi switch with Layer 3 capability, and it is configured through the switch's port and VLAN management tools rather than requiring separate physical hardware for each segment (UniFi Switching). A practical minimum for a leased office is four segments: staff, guest, payment/POS, and security devices (cameras plus door access), with the payment segment isolated most strictly given PCI considerations your payment processor will specify.
Ask your integrator how many SSIDs and VLANs the design actually needs — a small single-floor suite may not need the full segmentation a larger office uses, but payment terminals and door access devices should never share a broadcast domain with guest Wi-Fi.
How does UniFi Access secure the suite door?
UniFi Access controls the entry with a reader at the door tied to a PoE-powered access hub, which can be sized from a single-door hub to an Enterprise Access Hub supporting up to eight readers and doors with battery backup (UniFi Door Access Control Hubs). Readers support credential methods including NFC cards, keyfobs, PIN, and mobile wallet unlock, and can be paired with UniFi cameras so every entry event has matching video (UniFi Door Access). For a single-suite entrance, a single-door hub with one reader is typically enough; multi-door suites or shared-floor configurations are a reason to plan the larger access hub up front so adding doors later doesn't mean replacing the hub.
What should remote monitoring look like after move-in?
Once the network is live, the gateway, switch, and access points should all report into a centralized dashboard so firmware updates, uptime, and device health can be checked remotely instead of discovered during a service call. This is a question to raise directly with whoever designs the system — ask what gets monitored, how alerts are routed, and who has administrative access to make changes after handover. Cave Group's commercial services build this kind of integrated AV, networking, access, and lighting approach for offices and leasing centers, treating the network, cameras, and door access as one managed system rather than separate vendor relationships.
Frequently asked questions
Do I need a separate VLAN for payment terminals?
Yes — payment terminals should sit on their own VLAN, isolated from guest Wi-Fi and staff traffic, both for PCI compliance your payment processor will require and because isolating that traffic limits what a compromised device elsewhere on the network can reach.
What access point type fits a single-floor leased office?
UniFi's Enterprise Wi-Fi 7 access points are built for high-capacity, high-reliability environments with 10 GbE uplinks and support for over 1,000 connected devices per AP, which is typically more capacity than a single-floor office needs but gives headroom as device counts grow (UniFi Enterprise WiFi 7 Access Points).
Can one door hub handle more than one entrance?
A single Door Hub or Door Hub Mini is built for one door, while the Enterprise Access Hub supports up to eight readers and doors from one unit with battery backup support — worth specifying up front if your suite has more than one controlled entrance or may add one later.
Does the switch need to support Layer 3 routing?
If you want VLANs to communicate selectively (for example, allowing a staff device to reach a networked printer on another segment) without routing everything through the gateway, choose a switch from UniFi's Professional, Pro Max, or Enterprise families, since those are the tiers that support Layer 3 inter-VLAN routing.
Who should I talk to about segmenting a leased office network?
Ask whoever designs your fit-out's network how many VLANs the design includes, how door access and cameras are segmented, and what remote monitoring is in place after handover — these are standard questions for any commercial network build, not special requests.