MarineNovember 21, 20265 min read

Scoping Guest Casting to One Cabin on a Yacht

How to let a charter guest AirPlay or cast to their own cabin TV without exposing every screen on the vessel.

A charter guest who opens their phone's casting list should see their own cabin TV and perhaps the salon — not every screen on the vessel, and never a crew or control-system display. On a Crestron DM NAX system, that scoping starts with naming each zone's casting destination for its cabin and tying that zone's traffic to its own tagged network interface rather than a flat, shared one. Which devices can actually discover which zones is a broader network design question, so ask your network technician how discovery is scoped between the guest network and the crew, bridge, and control networks on your specific vessel, and have the answer confirmed in writing at commissioning.

Why shouldn't a guest's phone see every TV on board?

It shouldn't, by design, and the vessel's network should be built to keep it that way. Whether a guest device can even discover a TV outside their own cabin is a network-level question that sits above DM NAX's own settings — raise it directly with whoever designs and commissions the yacht's network, and ask for that boundary to be demonstrated with an actual guest device before you rely on it during a charter, rather than assumed from a diagram.

How does Crestron DM NAX scope casting to one cabin?

Each zone on a DM‑NAX amplifier gets its own dedicated streaming media player, and that player's casting visibility is controlled through the zone's Casting settings. Per the documentation, a friendly name entered in the Casting Name field "will be displayed as an available destination on the casting device" once AirPlay and/or Spotify Connect are enabled for that zone (Settings (DM‑NAX‑8ZSA)). That means a cabin's casting name should read as that cabin — "Owner's Suite" or "VIP Cabin 2" — not a generic label, so a guest scanning for destinations only recognizes and selects their own room.

DM NAX amplifiers also support Port Configuration, which lets an installer isolate and VLAN-tag traffic types across the unit's two physical LAN ports, with up to ten separate tagged interfaces available across the ports. The documentation notes that "if Port Configuration is enabled on the DM‑NAX‑8ZSA, the zone will appear on whichever adapter was assigned its Casting Zone from the Traffic Type drop-down list" (Settings (DM‑NAX‑8ZSA)). In practice this means a cabin's casting traffic can be tied to a specific tagged interface rather than sharing a flat management network with the control system. The smaller DM‑NAX‑4ZSA‑50 documents the same Port Configuration model and the same per-zone Casting section for its five zones, so the pattern scales down to a smaller vessel or a tender with fewer cabins.

Automatic Routing is the other setting worth getting right at commissioning. With it enabled, initiating a casting session routes the receiving media player to an output zone automatically — the documentation describes this mode as intended for use with Crestron Home OS or for setups where media players are named after rooms. With it disabled, a casting session does not route to a zone automatically; the route has to be set through programming or the Routing table instead, which fits setups where a media player is tied to a specific user rather than a fixed room. For a straightforward per-cabin casting scheme, automatic routing paired with cabin-named zones keeps the mapping between a zone's name and its physical cabin obvious at commissioning.

Who decides which VLANs can even discover a zone?

DM NAX's per-zone Casting Name and Port Configuration settings decide what a discoverable zone looks like and which tagged interface it sits on. Whether a guest device can discover that zone at all — versus a TV in another cabin, the crew mess, or a control-system display — depends on how the vessel's wider network is designed to handle discovery traffic between VLANs, which is outside what the DM NAX documentation itself specifies. Put that question directly to whoever designs and commissions the yacht's network: confirm, zone by zone, that a guest's casting list only populates with the destinations intended for them, and test it with an actual guest device before relying on it during a charter.

What should crew clear between charter guest groups?

Between charters, crew should treat both the DM NAX casting names and any paired sessions as items to reset, not assume they clear themselves. On the DM NAX side, this means reviewing each zone's AirPlay and Spotify Connect settings — confirming the Casting Name still matches the cabin and isn't left over from a previous naming convention, and that AirPlay passcodes, if used, have been rotated between groups. On the network side, ask your technician what the correct procedure is for clearing any guest devices that paired, bookmarked, or cached a connection to a specific cast destination, so the next charter group starts from a clean discovery list rather than inheriting a prior guest's session history. A fuller network and Crestron turnover checklist is covered in Charter Yacht Turnover: Resetting Crestron Between Guests.

Where this fits into the vessel's broader design

Cave Group designs yacht technology, including Crestron control and lighting, marine audio, and UniFi networking, as one coordinated package rather than separate systems bolted together after the fact. Getting guest casting scoped correctly belongs in the same design conversation as keeping crew, bridge, and control traffic on their own networks — it is worth raising during initial design or during a refit yard period rather than discovering the gap mid-charter. More on how Cave Group approaches onboard technology is on the marine page.

Frequently asked questions

Can a charter guest see every TV on the yacht by default?

Whether a guest device can discover TVs beyond their own cabin depends on how the vessel's wider network is designed to scope discovery traffic between the guest network and other onboard networks. Confirm with your network technician exactly how that boundary is set and test it with a guest device before a charter, rather than assuming it is handled automatically.

How does a DM NAX zone get a guest-friendly casting name?

Each zone has a Casting section in its settings with a Casting Name field; once AirPlay or Spotify Connect is enabled for that zone, the name entered there is what appears as a destination on the guest's casting device, per Settings (DM‑NAX‑8ZSA).

Does enabling Port Configuration on DM NAX change which guests see a zone?

Yes. With Port Configuration enabled, a DM NAX zone's casting traffic appears on whichever tagged network interface its Traffic Type assignment points to, so a zone can be tied to a dedicated interface rather than a flat management network shared with control, as described in Settings (DM‑NAX‑4ZSA‑50).

What should crew actually clear between charter groups?

Crew should check that each zone's Casting Name still matches the current cabin assignment, rotate any AirPlay passcodes, and ask their network technician to clear cached device pairings from the network controller so the next guest group doesn't inherit a previous group's casting history.

Is scoping casting a DM NAX setting or a network setting?

Both, in different ways: DM NAX's per-zone Casting Name and Port Configuration settings decide what a discoverable zone looks like and which tagged interface it's tied to, while which guest devices can discover that zone at all is a broader network design question to confirm with whoever commissions the vessel's network.

Sources

Work With Cave Group

Planning a yacht project?

Cave Group designs, installs, and supports these systems for luxury homes, hotels, and yachts across New York, New Jersey, and Europe — one partner from design through 24/7 support.

Start a Project

or explore our work